Car servicing - are you sitting down?

Inane baanter or words of wisdom - you decide...
Post Reply
User avatar
WiredWorm
Baaaaaa!
Baaaaaa!
Posts: 3162
Joined: Thu Dec 22, 2005 4:48 pm 0
Location: Right here on the edge of my seat......

Post by WiredWorm »

Wish me luck everyone - my Vectra has just gone in for servicing today at the local dealership. I'm sat here holding my breath hoping for the best.......
GamerTag: WiredWorm
It's like another mouth - LamptonWorm
User avatar
WiredWorm
Baaaaaa!
Baaaaaa!
Posts: 3162
Joined: Thu Dec 22, 2005 4:48 pm 0
Location: Right here on the edge of my seat......

Post by WiredWorm »

Ouch - I just had a call from the garage - service is done - £150.

However, they also found some other issues that they reckon need attention. They've quoted me £134 to have new disks and pads fitted.

They have also said that the front off-side shock absorber is badly leaking and the cost to repair that (and another issue related to the suspension) will be £390.

Oh yeah, and there's a problem with the exhaust and they've quoted me £362 to fix that. So let's see - i've just spent £150 and they now want to do another £886 worth of work on the car!! 8O

I think i'll ditch using the dealership and go visit a friend of mind who's a mechanic by trade. I suspect he'll charge rather a lot less than £800+.

Edit: I should perhaps add that I know precisely 'fuck all' about cars but I think i'm right in saying that they're charging a little over the odds there.
GamerTag: WiredWorm
It's like another mouth - LamptonWorm
User avatar
tufty
Sheepie Whore
Sheepie Whore
Posts: 12524
Joined: Fri Jan 07, 2005 4:52 pm 0
Location: French Alps

Post by tufty »

WiredWorm wrote:However, they also found some other issues that they reckon need attention. They've quoted me £134 to have new disks and pads fitted.

They have also said that the front off-side shock absorber is badly leaking and the cost to repair that (and another issue related to the suspension) will be £390.

Oh yeah, and there's a problem with the exhaust and they've quoted me £362 to fix that. So let's see - i've just spent £150 and they now want to do another £886 worth of work on the car!!
This sort of shit is 50% of the reason why I do my own mechanics. The other 50% is due to the fuckups I've had from "proper" mechanics, where vehicles come back in an unroadworthy condition.

Brake disks being in spec, and brake pads being usable, are both part of the MOT. If they need replacing now, it shouldn't have passed its MOT. If the discs are good enough to pass the MOT, they don't need replacing. Also, at that price, I seriously doubt they could replace both pads and discs for any kind of profit unless that's *just parts cost*. Just the discs are going to set you back a hundred quid or so, and pads don't generally leave you much (if any) change out of 50. so either they are doing you a favour, or you're about to get massively striped up.

If the pads are badly worn, it's probably time to change them anyway, but it's literally a 10 minute job unless they are corroded solid (in which case they wouldn't have passed the MOT, etc etc)

Shock absorbers are part of the MOT test. If they are leaking badly, or failing to do their job, the vehicle should not have passed its MOT. If they are working well enough to pass the MOT, there's no serious problem.
3. Examine each shock absorber for fluid leaks.

Note; Ensure that any fluid near the unit is from the shock absorber and not from another source, Slight seepage causing a thin fluid on a shock absorber is not a reason for rejection.
Exhaust is, yes, you guessed it, part of the MOT, and if it passed the MOT...

Simon
"massive retard™", "full of shit™", "tiny bitch™", "retarted™", "a bit of a one trick pony™", "petty™", "simple minded idealistic twat™", "miserable humourless fucker™"
User avatar
WiredWorm
Baaaaaa!
Baaaaaa!
Posts: 3162
Joined: Thu Dec 22, 2005 4:48 pm 0
Location: Right here on the edge of my seat......

Post by WiredWorm »

Thanks for the comments Simon - unfortunately the problem is that the MOT is due next month - so yeah, if these things ARE all wrong then yes it looks like I have some money to spend to get it through it's MOT.

Anyway, i've now collected the vehicle and have a list of what they wanted to do. Here goes........

1. All wipers smearing. They wanted to charge me £28 for new wipers. I think not. I may know fuck-all about cars but I KNOW that I can change a wiper blade.

2. Front Pads very low (they stated somewhere between 300-500 miles left on them). Front disks lipped slightly (i've had a friend check and he'd estimate a 2mm lip on the very outside rim of the disk). NSF disk corroding on the inside edge. £134 for this to be fixed. I'm assuming this would just be to have the front pads and disks done.

3. NSF shock absorber leaking - £122.80 for this to be fixed.

4. OSF coil spring broken - £199.90 to have a new pair fitted (they stated they can replace just the broken one but added that usually if they do that then the other one will fail soon after).

5. OSF anti-roll bar link arm worn to excess £68.15.

6. Middle box brackets corroded off and back box corroding and bracket. £362.72 for this.

So that's a grand total of £916.02 work that they want to do. Some of the above I can do myself - i've changed pads before so i'm comfortable with doing that. I'm not so sure that the disks really need doing. I'm going to get a friend to look at the suspension side of things and see what they can recommend but I suspect it won't come close to what i've been quoted by the dealership.

Oh yeah, and as for the exhaust. I find it hard to believe it sohuld be so expensive. I've already dug around and I can get a full exhaust system for my car for < £200.

Any more comments though would be greatly appreciated.

Cheers

Pete

Edit: I should perhaps add that as a result of this i'm going to be learning a LOT more about cars. I see fuck all reason to pay through the nose for stuff I can do myself.
GamerTag: WiredWorm
It's like another mouth - LamptonWorm
User avatar
peter_cushion
Baaaa!
Baaaa!
Posts: 943
Joined: Tue May 30, 2006 12:17 pm 0
XBL Gamertag: Peter Cuchion
Location: Ilkley, UK

Post by peter_cushion »

Image

Present for you Worm. :)
User avatar
WiredWorm
Baaaaaa!
Baaaaaa!
Posts: 3162
Joined: Thu Dec 22, 2005 4:48 pm 0
Location: Right here on the edge of my seat......

Post by WiredWorm »

peter_cushion wrote:Present for you Worm. :)
Thanks Peter - on my list to buy now. :)
GamerTag: WiredWorm
It's like another mouth - LamptonWorm
User avatar
tufty
Sheepie Whore
Sheepie Whore
Posts: 12524
Joined: Fri Jan 07, 2005 4:52 pm 0
Location: French Alps

Post by tufty »

WiredWorm wrote:Thanks for the comments Simon - unfortunately the problem is that the MOT is due next month - so yeah, if these things ARE all wrong then yes it looks like I have some money to spend to get it through it's MOT.
Ah, okay then
WiredWorm wrote:1. All wipers smearing. They wanted to charge me £28 for new wipers. I think not. I may know fuck-all about cars but I KNOW that I can change a wiper blade.
Instructions on the pack they come in :)
WiredWorm wrote:2. Front Pads very low (they stated somewhere between 300-500 miles left on them). Front disks lipped slightly (i've had a friend check and he'd estimate a 2mm lip on the very outside rim of the disk). NSF disk corroding on the inside edge. £134 for this to be fixed. I'm assuming this would just be to have the front pads and disks done.
Lipped, scored or corroded pads can be reskimmed, within limits. The main issue is that they stay within spec. It's a bit more tricky on ventilated disks, especially if the wear is uneven. This can save a lot of money especially if you have somebody who can reskim "cash in hand", disks are expensive.

If you've got corrosion on one face of a disk, it indicates that that pad isn't moving, so you'll want to sort that as well (pads out, clean up the caliper sliding surfaces, and copper grease on the various moving parts, although obviously not on the disks or pad surfaces themselves.)

Like I said, 130 quid is very cheap for front end disk and pad replacement, I can't see it covering both disks and the pads.

Disk removal isn't really an issue, usually it's a case of taking the wheel off, the pads out, unmounting the caliper (but leaving it connected to the hydraulic system) and undoing one or two screws that hold the disk in place. The only thing that's likely to cause problems is corrosion on various bolts, and not stripping the heads on the disk screws. You'll want access to a torque wrench and good quality sockets / drivers.

If you decide to do this yourself, borrow your friend (and his tools) to "give you a hand" :)quote]
WiredWorm wrote:3. NSF shock absorber leaking - £122.80 for this to be fixed.

4. OSF coil spring broken - £199.90 to have a new pair fitted (they stated they can replace just the broken one but added that usually if they do that then the other one will fail soon after).
Do the springs as a pair. You'll need spring retractors, again, borrow your friend. You should be able to get away with only replacing the one shock, but give the other one a good once-over and be prepared to have to replace it as well.
WiredWorm wrote:5. OSF anti-roll bar link arm worn to excess £68.15.
Pretty easy to swap out, again. Easier with a lift, because otherwise you'll be doing this on your back under the car.
WiredWorm wrote:6. Middle box brackets corroded off and back box corroding and bracket. £362.72 for this.
I assume they are talking about the brackets on the underside of the car, not the brackets on the exhaust itself? If so, you'll need someone who can weld.

If it's just the system that's shot, then you can replace the bits that need to be replaced and / or weld/braze new brackets onto the bits that will hold up. If you go for the latter approach, be aware that exhaust components tend to be zinc-coated, and brazing or welding onto zinc produces *very* dangerous fumes, you need to clean the zinc off first.

Fitting a new exhaust system once you have the old one off is a (relative) piece of piss, but do buy new clamps. Reusing old ones is a cunt of a job, as they are *always* corroded to buggery and the bolts snap.

For taking the old system off, soak everything in WD-40 the night before, and have a rubber mallet and large flatbladed screwdriver to hand. Also, you'll be lying on your back under the car fiddling with rusty bits, so wear eye protection, rusty steel flakes and soot in your eye are no fun.

The Haynes manual is a good buy, but be aware that their instructions are based on doing the work on a clean, non-corroded vehicle. If you can lay your hands on a factory service manual as well, that is always useful. I have it on good authority that certain service manuals are available in PDF form on the internets, but I wouldn't know anything about that :)

You do want good tools. It's worth spending the money to get quality, rather than stuff made from cheesecake that will mangle both itself and the thing you're working on. Also, "shop soap", overalls and latex gloves.

Simon
"massive retard™", "full of shit™", "tiny bitch™", "retarted™", "a bit of a one trick pony™", "petty™", "simple minded idealistic twat™", "miserable humourless fucker™"
User avatar
WiredWorm
Baaaaaa!
Baaaaaa!
Posts: 3162
Joined: Thu Dec 22, 2005 4:48 pm 0
Location: Right here on the edge of my seat......

Post by WiredWorm »

Cheers for that Simon, you've been a huge help.

It's very likely that i'll be doing to work alongside my friend - who i have to admit is pretty handy when it comes to this kind of work.

I'll report back with more news - but i'm feeling a bit happier about things now - it was indeed a good job I was sat down when they told me what they thought needed doing......
GamerTag: WiredWorm
It's like another mouth - LamptonWorm
User avatar
skab
Baaaaaa!
Baaaaaa!
Posts: 3448
Joined: Sat Apr 27, 2002 1:53 am 0
Location: Barnyard, Ruhr area, Germany

Post by skab »

hairy_pete wrote:If the control system is anything like the Citroën XM's, then check your sensors first. The XM monitors throttle, brake, steering, speed, sideways acceleration, and ... drum roll ... the most frequently overlooked one, open doors.
I already replaced the sensors that check the vertical acceleration (read: how bad the road is), didn't help. Now I have to check the fault memory again if there is something that points to broken shock absorbers (or rather if the coils in the valves that control them have shorted), and for that I first have to get my diagnosis system running. I won't go to a BMW garage again where they spend 30min picking their nose, then print out the report from the system and show it to me cluelessly, hoping that maybe I know what all that actually means. And then charge me 30 Euros for sheer incompetence.
User avatar
dom
Baaaaa!
Baaaaa!
Posts: 1370
Joined: Wed Feb 09, 2005 1:17 pm 0
Location: Edinburgh, UK and level 691859
Contact:

Post by dom »

My golf started leaking steam and got very hot on the way home, time to get out the Haynes manual for me too...

...or it's time to get a new(er) car :D

funfunfun
OMG (or oligodendrocyte myelin glycoprotein) is a molecule found in your central nervous system.
User avatar
piku
Sheepie Whore
Sheepie Whore
Posts: 20960
Joined: Wed Apr 24, 2002 10:44 am 0
Website: Http://Www.ncot.uk
Location: Wakefield
Contact:

Post by piku »

Gah my turn now. My car's in the garage having just failed its MOT, which comes as no surprise to me.

The little MOT man says:

1. The passenger side wing mirror cannot be ductaped on
2. The disks and pads need replacing
3. New brake fluid
4. Number plate bulb out
5. New Cambelt, fanbelt and retension
6. New front tyre
7. My driver's seat is loose
8. Front exhaust has hole
9. Wheel alignment wrong

So yeah... bye bye £400ish

Time for a new car I think, but I can't afford it so need to keep patching this one up.

At least they haven't complained about the scuffed wing mirror or said it needs an oil change and new oil filter. Or helpfully replaced my radiator water and washer water. I like it how garages charge you a fiver to drain and replace water.

I kind of expected 2, 8, 9 and 6. I was gently gassing myself to death when sat at lights. One night I clobbered a large rock that'd fallen off a drystone wall. It was just lying there in the road and I had a choice between hitting it or hitting the oncoming cars.

Sodding numberplate bulbs do my nut. I check every other bulb quite regularly but always forget that one. I even have a spare set of bulbs in my car.

My seat's been wobbly for ages. It's good garages don't check irritating things like leaky sunroofs, smeary window wipers, funny smells or "sometimes it doesn't go into reverse" since I'd be screwed :lol:

It'll be nice to have a working passenger wing mirror too.

I'm glad I get paid on Friday!
return (0);
User avatar
punkrulesok
Baaaaaa!
Baaaaaa!
Posts: 2936
Joined: Sun Jun 09, 2002 9:17 am 0
Yahoo Messenger: punkrulesok@yahoo.com
Location: Wirral, UK.
Contact:

Post by punkrulesok »

Piku - wheel tracking is not an MOT fail (as far as i know), although if the tracking is out, it'll do your tyre in quickly. I'd check this out?

Also - the new cambelt is going to be your most expensive item there.
User avatar
piku
Sheepie Whore
Sheepie Whore
Posts: 20960
Joined: Wed Apr 24, 2002 10:44 am 0
Website: Http://Www.ncot.uk
Location: Wakefield
Contact:

Post by piku »

punkrulesok wrote:Piku - wheel tracking is not an MOT fail (as far as i know), although if the tracking is out, it'll do your tyre in quickly. I'd check this out?
Yeah the passenger front tyre needed replacing too. Mostly because there's a bulge on it where I smacked the afrementioned rock. Smashed the wheel trim up a bit too.

The tracking was way off, now it's been reset I can appreciate just how bad it was. The car went in a straight line before, but the steering wheel jiggled around. Now the only thing I feel through the steering wheel is the uneven road and that giant rut the lorries have made down the M62.
Also - the new cambelt is going to be your most expensive item there.
£100 for one of those, new timing belt and the one that goes to the alternator. The belt going to the alternator did need replacing, it used to squeal in the cold.

Seems they've adjusted the timing of the engine too, it doesn't sound like it's about to stall all the time.

It's nice having working brakes again :) I don't have to anticipate stopping 10 seconds before actually needing to do it.

I swear though there's someone who goes around pre MOT cars and breaks their numberplate light. Every time I've taken my car for an MOT it's needed that bulb replacing.

I've just spent a fair chunk of money, but it was less than buying a new car.

I might check the oil again, they don't appear to have replaced it. I think it needs more.

They had to attack the exhaust with a welder before I left though. I got in the car, started it and was treated to a loud banging noise. Seems the exhaust was banging on the bottom of the car. Fixing this required three people, a large hammer, crowbar and a welding torch. One man to weld, one to hit, and one to swing off the exhaust.
return (0);
User avatar
TT
Baaaaaa!
Baaaaaa!
Posts: 2174
Joined: Wed Jun 18, 2003 3:53 pm 0
Location: Not Derbyshire
Contact:

Post by TT »

28 quid to change wiper blades! 8O
Be strong, and Shout at the Devil...
User avatar
WiredWorm
Baaaaaa!
Baaaaaa!
Posts: 3162
Joined: Thu Dec 22, 2005 4:48 pm 0
Location: Right here on the edge of my seat......

Post by WiredWorm »

TT wrote:28 quid to change wiper blades! 8O
Well to change AND supply them - i'm not sure but I think official Vauxhall wiper blades are gold plated - or at least that what i'd think for them to cost THAT much.

I'll change them myselves. I've got a friend dropping some brake pads off for me and i'll fit them myselves too.

As for the rest - I think i'll take it to MOT and see what it fails on before I start going loads of additional work that may not be required. And anything that does need doing (coil spring for example) will be handled by a friend of mine.
GamerTag: WiredWorm
It's like another mouth - LamptonWorm
Post Reply