Car servicing - are you sitting down?

Inane baanter or words of wisdom - you decide...
Post Reply
User avatar
hairy_pete
Baaaaaaa!
Baaaaaaa!
Posts: 7217
Joined: Mon May 27, 2002 8:10 pm 0
Location: A Tiny Village in Bavaria

Post by hairy_pete »

punkrulesok wrote:you should check the gearbox oil level if the transmission is sounding rough. over years, even if there's no leaks, it can gradually go down as the oil is "whisked" about by the gears.

the gearbox oil is one of those things that doesn't get checked by most services :roll:.
That would be because most makers now advertize their gearbox oil as "lifetime fill, no service required". Well duh, sure it's a lifetime oil fill, because when the oil's gone, gearbox life ends.

They don't make 'em like they used to ... Citroëns used to have oil level probe stick wossnames in their gearboxes, even the manual ones.
User avatar
chris4500uk
Baaaaa!
Baaaaa!
Posts: 1158
Joined: Thu Feb 26, 2004 3:05 am 0
Location: Middlesbrough, UK
Contact:

Post by chris4500uk »

I just got my timing belt kit done with water pump for £250 by a VAG specalist

Car is a polo 1.9tdi

cheap :wink:
User avatar
Munky
Baaaaaa!
Baaaaaa!
Posts: 2209
Joined: Fri Sep 10, 2004 7:11 pm 0

Post by Munky »

chris4500uk wrote:I just got my timing belt kit done with water pump for £250 by a VAG specalist

Car is a polo 1.9tdi

cheap :wink:
You took your car to a gynaecologist?
User avatar
Kelloggs
Baaaaa!
Baaaaa!
Posts: 1859
Joined: Wed Jun 22, 2005 11:38 pm 0
XBL Gamertag: TheAntiKelloggs
Location: Widnes or Altrincham. Take your pick.

Post by Kelloggs »

Latest news from the front line: total clutch collapse.

I was heading over to New Brighton to see a friend. Came off the roundabout, turning left, put my foot on the clutch to change up to second (so, the car was in neutral for a fraction of a second) and the clutch-pedal hit the floor. No resistance whatsoever, and no clutch actuation either. I pulled into the side and parked on momentum alone.

Insurers called; recovery arranged; now back home. Recovery bloke guessed that the slave cylinder had gone. I'm guessing that, if I hadn't had them poking round fitting a new clutch, the car would still be capable of movement.

Be under no illusions; the Ford dealer's servicing department is in for an absolute roasting on Monday morning.
User avatar
Ryan
Baaaaa!
Baaaaa!
Posts: 1634
Joined: Sun Feb 09, 2003 10:28 pm 0
Location: Gelderland, Netherlands
Contact:

Post by Ryan »

Ely wrote:The clutch going that soon suggests either it was defective or you can't drive properly. I'm going for the former, unless you tell us you start off everywhere in 2nd gear like my Grandad used to! In twenty years of driving cars I've never had a clutch go on me, and I'd had much older cars than your 2 years. Maybe do some research to see if it's a common/know issue with Mondeos of that age.

As for the cost it doesn't surprise me really. I've just had a 40k service and CAM belt change for my Golf TDI and those two didn't give me any change from a grand. With labour at about 50quid an hour it's hardly surprising and this wasn't a VW Dealer, just a little VW/Seat/Audi specialist near where I work.
I've worked in the industry for a bit, saw lots of problems with clutches.

Unless you never use the clutch to change gears or drive full speed with clutch half on, then the problem's warranty.

Shout about it, and they'll refund ya.
User avatar
hairy_pete
Baaaaaaa!
Baaaaaaa!
Posts: 7217
Joined: Mon May 27, 2002 8:10 pm 0
Location: A Tiny Village in Bavaria

Post by hairy_pete »

Kelloggs wrote:Latest news from the front line: total clutch collapse.

I was heading over to New Brighton to see a friend. Came off the roundabout, turning left, put my foot on the clutch to change up to second (so, the car was in neutral for a fraction of a second) and the clutch-pedal hit the floor. No resistance whatsoever, and no clutch actuation either. I pulled into the side and parked on momentum alone.

Insurers called; recovery arranged; now back home. Recovery bloke guessed that the slave cylinder had gone. I'm guessing that, if I hadn't had them poking round fitting a new clutch, the car would still be capable of movement.
Fitting a new clutch, they should certainly have spotted leaky hydraulics. After all, the original fault may just as well have been gradually retracting clutch, exactly from the leaky cylinder.
Be under no illusions; the Ford dealer's servicing department is in for an absolute roasting on Monday morning.
Absolutely. Don't "roast" though ... Remember to stay 100% calm and polite, yet still, don't move a millimeter from your position in the argument. That works a lot better, I found.
User avatar
kalmar
Baaaaaaa!
Baaaaaaa!
Posts: 8293
Joined: Fri Jun 24, 2005 2:46 pm 0
Location: Fife

Post by kalmar »

hairy_pete wrote:
Kelloggs wrote:Latest news from the front line: total clutch collapse.

I was heading over to New Brighton to see a friend. Came off the roundabout, turning left, put my foot on the clutch to change up to second (so, the car was in neutral for a fraction of a second) and the clutch-pedal hit the floor. No resistance whatsoever, and no clutch actuation either. I pulled into the side and parked on momentum alone.

Insurers called; recovery arranged; now back home. Recovery bloke guessed that the slave cylinder had gone. I'm guessing that, if I hadn't had them poking round fitting a new clutch, the car would still be capable of movement.
Fitting a new clutch, they should certainly have spotted leaky hydraulics. After all, the original fault may just as well have been gradually retracting clutch, exactly from the leaky cylinder.
Absolutely. I suggested it would be more likely to be a stretched clutch cable (or hydraulics in this case). Probably they 'cured' the problem when they adjusted it after fitting the new clutch, if they even fitted one.

Don't rant at them but get all the facts you can calmly and politely, and then escalate it like hell.
(just show, no stabby stabby)
User avatar
piku
Sheepie Whore
Sheepie Whore
Posts: 20960
Joined: Wed Apr 24, 2002 10:44 am 0
Website: Http://Www.ncot.uk
Location: Wakefield
Contact:

Post by piku »

hairy_pete wrote:It's the aforementioned "high gear soft-engage while accelerating" technique that literally burns the pad off.
So you should smoothly and quickly lift your foot off the clutch when changing gears at speed?
Other related mistakes and their damage: Engaging too hard from zero velocity can ruin the damper springs.
That'll be why my car goes *clunk* when setting off then... It's impossible to smoothly set off in my car, I've tried various combinations of accelerator and clutch. At first I thought it was my driving, but I can do it fine in any other car or van.
Keeping the clutch depressed while halted grinds away at the clutch bearing.
I do that when at traffic lights, but when stuck in traffic jams and whatnot I stick it in neutral. It's either that or my leg goes to sleep. And I make sure I'm not riding the clutch by putting my left foot on the floor.

Would mis-aligned/balanced front wheels (caused by hitting the kerb at speed and once hitting a large rock in the middle of the sodding road) cause the CV joins to wear quicker than usual?
return (0);
User avatar
PVB
Sheepie Whore
Sheepie Whore
Posts: 32542
Joined: Mon Apr 22, 2002 10:16 pm 0
XBL Gamertag: PVBuk
PSN: PVBuk
Location: Medway, U.K.

Post by PVB »

piku wrote:
hairy_pete wrote:It's the aforementioned "high gear soft-engage while accelerating" technique that literally burns the pad off.
So you should smoothly and quickly lift your foot off the clutch when changing gears at speed?
Yes, never hold the clutch pedal in for longer than absolutely necessary.
User avatar
hairy_pete
Baaaaaaa!
Baaaaaaa!
Posts: 7217
Joined: Mon May 27, 2002 8:10 pm 0
Location: A Tiny Village in Bavaria

Post by hairy_pete »

piku wrote:
hairy_pete wrote:It's the aforementioned "high gear soft-engage while accelerating" technique that literally burns the pad off.
So you should smoothly and quickly lift your foot off the clutch when changing gears at speed?
Yes. The art in upshifting lies in the timing - clutch, shift, reengage exactly when the engine's falling revs match the next gear's ratio. If you get that timing perfectly right, you can even upshift without using the clutch at all - without causing any nasty noises or gearbox wear. Don't try this at home.

When downshifting, the timing trick is to rev the engine up just in the right moment with the clutch reengaging.

Up or down, you never use clutch slip to compensate for rev mismatch.
Other related mistakes and their damage: Engaging too hard from zero velocity can ruin the damper springs.
That'll be why my car goes *clunk* when setting off then... It's impossible to smoothly set off in my car, I've tried various combinations of accelerator and clutch. At first I thought it was my driving, but I can do it fine in any other car or van.
Most definitely. My Citroën DS was like that too, absolutely impossible to drive off smoothly.
Keeping the clutch depressed while halted grinds away at the clutch bearing.
I do that when at traffic lights, but when stuck in traffic jams and whatnot I stick it in neutral. It's either that or my leg goes to sleep. And I make sure I'm not riding the clutch by putting my left foot on the floor.
It's better to learn guesstimate when the lights will go green. To minimize foot-on-clutch time, put 1st gear in just a couple of seconds before that happens.
Would mis-aligned/balanced front wheels (caused by hitting the kerb at speed and once hitting a large rock in the middle of the sodding road) cause the CV joins to wear quicker than usual?
If that kind of bump damages the front suspension, your car's crap anyway ;)
Seriously, nah, CV joints don't suffer from such slight misalignment. You need a lot more "wrong angle" for that. They do suffer from seriously wrong ride height (an exclusive Citroën phenomenon ;) if it weren't for the DIY lowered-suspension crowd). The #1 reason however is running them dry. Check your rubber sealbags (don't forget there's four of these!).
User avatar
Kelloggs
Baaaaa!
Baaaaa!
Posts: 1859
Joined: Wed Jun 22, 2005 11:38 pm 0
XBL Gamertag: TheAntiKelloggs
Location: Widnes or Altrincham. Take your pick.

Post by Kelloggs »

hairy_pete wrote:
Kelloggs wrote:Be under no illusions; the Ford dealer's servicing department is in for an absolute roasting on Monday morning.
Absolutely. Don't "roast" though ... Remember to stay 100% calm and polite, yet still, don't move a millimeter from your position in the argument. That works a lot better, I found.
Ah, no, I was intending to be just exactly as polite as it took. I gave my friend a ring as I failed to get to his house (about 1/4 mile away) and he came out to see if he could help. He pointed out that it could easily have been serious, if I'd panicked and hit the brakes instead of letting it freewheel. I pointed out to him, I'm not really the panicking kind. He had to agree.

No, I've sent Ford a politely-worded message via their online-service website (whose space is, in any case, far too small for a rant) and advised them of the situation, and that I will be expecting it to be investigated As Soon As Possible. Which will, of course, be Monday, after which I shall be Enquiring Further as to the details of the matter. No, I'm not the roasting kind, either, but this could have gone so very much worse.
User avatar
chris4500uk
Baaaaa!
Baaaaa!
Posts: 1158
Joined: Thu Feb 26, 2004 3:05 am 0
Location: Middlesbrough, UK
Contact:

Post by chris4500uk »

the clutch and brakes are on the same cylinder ???

i never knew that
User avatar
Kelloggs
Baaaaa!
Baaaaa!
Posts: 1859
Joined: Wed Jun 22, 2005 11:38 pm 0
XBL Gamertag: TheAntiKelloggs
Location: Widnes or Altrincham. Take your pick.

Post by Kelloggs »

chris4500uk wrote:the clutch and brakes are on the same cylinder ???

i never knew that
No, I don't think so. Probably better to read it as, "it could have been serious if I'd panicked (and, for example, hit the brakes)".
User avatar
punkrulesok
Baaaaaa!
Baaaaaa!
Posts: 2936
Joined: Sun Jun 09, 2002 9:17 am 0
Yahoo Messenger: punkrulesok@yahoo.com
Location: Wirral, UK.
Contact:

Post by punkrulesok »

Kelloggs wrote:
chris4500uk wrote:the clutch and brakes are on the same cylinder ???

i never knew that
No, I don't think so. Probably better to read it as, "it could have been serious if I'd panicked (and, for example, hit the brakes)".
Some cars (most Fords) share the same fluid tank.

By the way - un-smooth clutch action could be down to the release bearing. But as with 90% of clutch problems you've got to whip the gearbox off to fix. Once that's off you may as well replace all the parts you can, as it's so expensive in Man hours (in a garage).
User avatar
tufty
Sheepie Whore
Sheepie Whore
Posts: 12524
Joined: Fri Jan 07, 2005 4:52 pm 0
Location: French Alps

Post by tufty »

punkrulesok wrote:
Kelloggs wrote:
chris4500uk wrote:the clutch and brakes are on the same cylinder ???

i never knew that
No, I don't think so. Probably better to read it as, "it could have been serious if I'd panicked (and, for example, hit the brakes)".
Some cars (most Fords) share the same fluid tank.
Citroens, too. Yes, I've just spent the better part of the weekend under a BX.
"massive retard™", "full of shit™", "tiny bitch™", "retarted™", "a bit of a one trick pony™", "petty™", "simple minded idealistic twat™", "miserable humourless fucker™"
Post Reply